Información del personal investigador

Autoría: MARCOS SÁNCHEZ MATÍAS, SERGIO CICERO GONZALEZ, BORJA ARROYO MARTINEZ, GIOVANNI BONNY, HELEN SWAN, PETTERI LAPPALAINEN, EBERHARD ALTSTADT, TOM PETIT, FLORIAN OBERMAIER

2023

Fracture load estimations for U-notched and V-notched 3D printed PLA and graphene-reinforced PLA plates using the ASED criterion

Artículo de Revista

Frattura ed Integrita Strutturale, 2023, 66, 322-338

Autoría: SERGIO CICERO GONZALEZ, SERGIO ARRIETA GOMEZ, MARCOS SÁNCHEZ MATÍAS

2023

Predicting critical loads in fused deposition modeling graphene-reinforced PLA plates containing notches using the point method

Artículo de Revista

Polymers, 2023, 15, 3797

Autoría: SERGIO CICERO GONZALEZ, MARCOS SÁNCHEZ MATÍAS, SERGIO ARRIETA GOMEZ

2023

Fracture Load Prediction of Non-Linear Structural Steels through Calibration of the ASED Criterion

Artículo de Revista

Metals, 2023, 13, 1211

Autoría: MARCOS SÁNCHEZ MATÍAS, SERGIO CICERO GONZALEZ, SERGIO ARRIETA GOMEZ, ALI REZA TORABI

01/07/2023

Calibración del criterio SED para la estimación de cargas de rotura del acero estructural S275JR con comportamiento no-lineal

Artículo de Revista

Revista Española de Mecánica de la Fractura, 2023, 6, 21-26

Autoría: MARCOS SÁNCHEZ MATÍAS, SERGIO CICERO GONZALEZ, SERGIO ARRIETA GOMEZ

2023

Using mini-CT specimens for the fracture characterization of ferritic steels within the ductile to brittle transition range: a review

Artículo de Revista

Metals, 2023, 13(1), 176

Autoría: MARCOS SÁNCHEZ MATÍAS, SERGIO CICERO GONZALEZ, MARK KIRK, EBERHARD ALTSTADT, WILLIAM SERVER, MASATO YAMAMOTO

01/01/2023

Fracture characterization of structural steel S275JR using conventional ct specimens, mini-ct specimens and small punch specimens: a comparison

Artículo de Revista

American Society of Mechanical Engineers, Pressure Vessels and Piping Division (Publication) PVP

Autoría: BORJA ARROYO MARTINEZ, SERGIO CICERO GONZALEZ, MARCOS SÁNCHEZ MATÍAS

2023

Estimation of load bearing capacity in 3d printed pla notched plates using the theory of critical distances

Comunicación a Congreso

Proceedings of the ASME 2023 Pressure Vessels & Piping Conference: volume 5 materials & fabrication

Autoría: SERGIO CICERO GONZALEZ, SERGIO ARRIETA GOMEZ, MARCOS SÁNCHEZ MATÍAS

2023

39 resultados

1 de 2

Volver

Estamos realizando la búsqueda. Por favor, espere...

Researchers portal

Portal del personal investigador

MARCOS SÁNCHEZ MATÍAS

Identificadores

Structural integrity evaluation of three-dimensional-printed graphene-reinforced polylactic acid notched plates using failure assessment diagrams

On the possibility of extending the crack length criterion in the master curve methodology

Mini-C(T) specimens for Master Curve analysis of structural steels operating within their ductile-to-brittle transition region

Using the point method to estimate failure loads in 3D printed graphene-reinforced PLA notched plates

Notch effect in acrylonitrile styrene acrylate (asa) single-edge-notch bending specimens manufactured by fused filament fabrication

Validity of toughness measurements from miniature specimens failing in different fracture modes

Fracture characterization of structural steel S690Q by using mini-CT specimens

Aplicación del diagrama de fallo a placas de PLA reforzado con grafeno fabricadas mediante impresión 3D

Caracterización a fractura de los aceros estructurales S355J2 y S460M mediante el uso de probetas mini-C(T)

Project FRACTESUS: fracture toughness round robin on a high copper weld using miniature C(T) specimens- results and discussion

Validity of toughness measurements from miniature specimens failing in different fracture modes

Structural integrity evaluation of 3D printed graphene-reinforced PLA notched plates using failure assessment diagrams

On the possibility of extending the crack length criterion in the master curve methodology

On the use of mini-CT specimens to define the Master Curve of unirradiated reactor pressure vessel steels with relatively high reference temperatures

Analysis of additively manufactured notched PLA plates using failure assessment diagrams

Estimation of fracture loads in 3D printed PLA notched specimens using the ASED criterion

FRACTESUS Project overview: objectives, organisation and initial findings

Fracture load estimations for U-notched and V-notched 3D printed PLA and graphene-reinforced PLA plates using the ASED criterion

Predicting critical loads in fused deposition modeling graphene-reinforced PLA plates containing notches using the point method

Fracture Load Prediction of Non-Linear Structural Steels through Calibration of the ASED Criterion

Calibración del criterio SED para la estimación de cargas de rotura del acero estructural S275JR con comportamiento no-lineal

Using mini-CT specimens for the fracture characterization of ferritic steels within the ductile to brittle transition range: a review

Fracture characterization of structural steel S275JR using conventional ct specimens, mini-ct specimens and small punch specimens: a comparison

Estimation of load bearing capacity in 3d printed pla notched plates using the theory of critical distances